Slip resistant coating for checkerplate?
Submitted: Monday, Sep 17, 2007 at 16:22
ThreadID:
49792
Views:
6401
Replies:
7
FollowUps:
16
This Thread has been Archived
Member - Tonester (VIC)
Hi all.
Has anyone got a good idea for putting some sort of slip-stop coating on checkerplate?
Have the checkerplate on top of my steel sliders, and am constantly slipping off the edge (not much toe room b/w it and the sill). My wife and kids slip more than I do - which means I hear about it all the time. :-)
I have got a stick-on outdoor tread (Bunnings) to put on, say, the smooth steel tubes, but it won't stay stuck to checkerplate on top.
Ideas...?
Tone
Reply By: Member - Oldplodder (QLD) - Monday, Sep 17, 2007 at 16:41
Monday, Sep 17, 2007 at 16:41
I would have suggested the stick on stuff in strips, but it doesn't apply to floor plate as
well as you said. I think chequerplate went out a good few years ago :o)
For a boat deck, we used to use decking paint with a non slip finish.
Essentially it was fine sand mixed into the paint, or you can sprinkle the sand on after a coat and a light coat of paint over the top.
AnswerID:
262692
Follow Up By: Member - Kiwi Kia - Monday, Sep 17, 2007 at 16:47
Monday, Sep 17, 2007 at 16:47
What's the possibility of removing the chequer plate (probably pop riveted on) and turning it up-side down. The stick-on anti slip material would then be able stick to to the smooth surface.
FollowupID:
524194
Follow Up By: Member - Vince B (NSW) - Monday, Sep 17, 2007 at 17:37
Monday, Sep 17, 2007 at 17:37
HI
john.
Just bought a new of sets for the NP with checkerplate decking. I will await replies as my plate is welded onto the frame.
Regards.
Vince
FollowupID:
524199
Follow Up By: Member - Tonester (VIC) - Monday, Sep 17, 2007 at 18:19
Monday, Sep 17, 2007 at 18:19
Oldplodder, I wondered if there was a coarse and durable paint available. Will have a look at decking paint, maybe speak with a paint pro too.
Kiwi, yes, riveted on. If I dril them out I think I'll have rattly bits floating in the steel tube.
FollowupID:
524205
Reply By: Member - Royce- Monday, Sep 17, 2007 at 23:53
Monday, Sep 17, 2007 at 23:53
Not sure how 'agricultural' you're willing to go. Had a small accident early this year with my wifes Hilux. Ended up using a line of gal tech screws to make a repair. Bonus was that the step is non slip now.
Maybe a few tech screws in just the right spot... maybe wreck the looks.. but would do the trick.
Slips are extremely dangerous. I reckon slipping off bits is the way I have hurt myself the most over the years. I slipped off the back of my old Troopie on our trip around Oz in 1994. Was left hanging by my wedding ring. Had to cut it off with tin snips, it was so deformed.
Cheers Royce
AnswerID:
262790
Follow Up By: Member - Tonester (VIC) - Tuesday, Sep 18, 2007 at 08:30
Tuesday, Sep 18, 2007 at 08:30
thanks Royce
FollowupID:
524338
Reply By: Anthony (Vic) - Tuesday, Sep 18, 2007 at 10:05
Tuesday, Sep 18, 2007 at 10:05
We had the same issue with or cherker plate step on the camper.
An effective fix was found after a trip to Clark Rubber. They have a stick on strip, which will stick great to checkerplate.
Before I applyed the strip, I buffed up the checkerplate with a rotary wire brush in the electric drill. The strip have been on for over a year and not a
sign of coming off.
No more slips, even with muddy boots.
cheers Anthony
AnswerID:
262821
Follow Up By: Member - Tonester (VIC) - Tuesday, Sep 18, 2007 at 11:39
Tuesday, Sep 18, 2007 at 11:39
ok, thanks Anthony. Will have a look.
FollowupID:
524377
Follow Up By: Member - MUZBRY (VIC) - Tuesday, Sep 18, 2007 at 12:26
Tuesday, Sep 18, 2007 at 12:26
Tony
I can get you a "Self adhesive stair tread" if you wish.
They are 610 x 190 x 3 mm Chequer plate rubber. I am not sure that will be anti slip , but that is what they are made for.
Murray
FollowupID:
524384
Follow Up By: Member - MUZBRY (VIC) - Tuesday, Sep 18, 2007 at 12:35
Tuesday, Sep 18, 2007 at 12:35
Tony
Its called "SLIP TAPE" and is available at Bunnings or BOC ? been advised by a sister in law and they know all.....
Murray
FollowupID:
524386
Follow Up By: Member - Tonester (VIC) - Tuesday, Sep 18, 2007 at 13:40
Tuesday, Sep 18, 2007 at 13:40
Murray, confused a bit. Is the "slip tape" the same as "self adhesive stair tread" in your posts? And are they the same as Anthony's suggestion of Clark Rubber..?
Tone
FollowupID:
524395
Follow Up By: Member - MUZBRY (VIC) - Wednesday, Sep 19, 2007 at 07:21
Wednesday, Sep 19, 2007 at 07:21
Tony
quite possible. The product we used to use was black and rough like emery paper.The back was a peal off stick back. I had rolls of this product that was 100mm wide and was cut to suit.
Clark rubber. I have never used them as i know where they buy their product and for how much.
I will try and buy a roll, maybe others will want some.I will let you have it at my cost plus postage. Give me a couple of days.
Murray
FollowupID:
524473
Follow Up By: Member - Tonester (VIC) - Wednesday, Sep 19, 2007 at 08:56
Wednesday, Sep 19, 2007 at 08:56
Thanks Muzbry. Before you buy, pls call me though. You got my number (in recent emails). If its the Bunnings stuff, damn sure I have it already. 3M, Safety Walk Outdoor Tread. If its other, then certainly interested in what it is exactly.
FollowupID:
524485
Follow Up By: Anthony (Vic) - Wednesday, Sep 19, 2007 at 09:04
Wednesday, Sep 19, 2007 at 09:04
Hi Tonester
The stick on tape I bought at Clark Rubber is sold by the metre. It comes in various widths, mostly back, some with balck and yellow
hazard pattern. Its surface is like a rough sandpaper, similar to the on slip surface on skateboards.
I don't recall the cost but wasn't that much. cheers A
FollowupID:
524487
Follow Up By: Member - Tonester (VIC) - Wednesday, Sep 19, 2007 at 10:53
Wednesday, Sep 19, 2007 at 10:53
thanks Anthony
FollowupID:
524513